![]() But you can assign a scope box to multiple views easily. So until an architect has this need, I'll just make do with the work-around. If you do then the View Template has a very limited use across the project, especially for large projects. So in fact, you don’t have to resize every view individually. Whenever you change the size of the Scope Box, every view that is assigned to this box will change as well. But hey, it wasn't too long ago that you couldn't slope waste, vent, and storm water piping in Revit. A Scope Box in Revit is a 3D transparent-looking box that can be used to crop (multiple) views with ease. If we could only get Levels to be at a slope, or be able to set pipe/duct offsets based on a reference plane, it would be a lot easier. Setting the pipe elevations using dimensions off of annotation lines drawn along the bottom of the utilidor (rather than having 7 different Levels within a 5 ft range). I instead created separate "Upper" and "Lower" Floor Plans (not Dependent Views) for each manhole, set the X & Y plan layout to the Scope Box for that manhole to straighten it out for the sheet presentation, and then set the View Range independently for each manhole Floor Plan. Scope boxes just can't do that yet (or at least Revit 2018) and the vertical view within Floor Plans are instead only adjustable through the View Range.įurther working the model, I discovered your comment that all of the Dependent Views are locked into the View Range of the original plan. Thank you kubsix! I believe you have the answer there. To draw a scope box, click in the upper left. Select the scope box, and on the Properties palette, enter a value for the Name property. Tip: You can also change the name of the scope box after creating it. On the Options Bar, enter a name and specify a height for the scope box, if desired. Unless Revit figured out a way to have a sloped Level (oxymoron) or allow Reference Planes to be used as the basis for View Ranges?Īm I missing a setting to make scope boxes cut in the 'z' direction? Ideas on how to make this work? In a plan view, click View tab Create panel (Scope Box). ![]() The utilidor slopes as well so it is not as easy to set two universal Levels and use the View Range. Sure, I could use the View Range within each plan view to accomplish this but I was hoping to use the grips on the scope boxes to visually dial in where the separation occurs. The function updates the scopeboxes and maintains all scope box selections. By control I mean a view can be assigned to a scope box and the boundary of the scope box will govern the crop region. ![]() ![]() Looking at the tutorials, scope boxes can cut 3D views in the 'z' axis, but I can't figure out how to use the scope box to cut the 'z' direction in plan views. This application is used to delete unused Scope Boxes from a Revit project. Scope boxes are intended to control the crop regions of views and datum such as Reference Planes, Levels and Grid Lines. But both plan views of the "upper" and "lower" scope boxes show the piping through both scope boxes. Since I already had the scope boxes around each of these areas, I thought I could just copy the scope box and have one for the "upper" half and one for the "lower" half. My issue is, I want to show in plan view the piping in the upper half of the utilidor and a separate plan view of the piping in the lower half of the utilidor. I utilized Scope Boxes and Dependent Views to present large scale views of the utilidor where there are piping branches (manholes) and to present these in nice, perpendicular views on the plan sheets. Any action you may take based on the information provided is strictly at your own risk, and the author(s) will not be liable for any losses and damages in connection with the use of the content.I am working on a utilidor project that has multiple angles and levels of piping. All information is provided as-is with no warranty whatsoever. ![]() The opinions and views expressed in the content are those of the author and not the author's employer or any other person or entity. Autodesk, AutoCAD, DWG, the DWG logo, and Revit are registered trademarks or trademarks of Autodesk, Inc., and/or its subsidiaries and/or affiliates in the USA and other countries. Autodesk screen shots reprinted courtesy of Autodesk, Inc. This website is not sponsored by, affiliated with, or endorsed by Autodesk. Camara (All Rights Reserved), unless otherwise noted. OReilly members experience books, live events, courses curated by job role.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |